– Compact, rugged design with large color screen
– Compatible with monophasic, biphasic and pulsed waveforms
– Rechargeable battery allowing operation without the need for mains power
– ECG simulation with high level output
– Reliable and non-inductive defibrillator test load of 50Ω
Available in the US – Call 813 886 2775
Datasheets
Manual
Manual
Datasheets
Datasheets
| AED Pulse Mode Waveforms | |
|---|---|
| Normal Sinus Rhythm (NSR) | 20 – 300 BPM, Amplitude 1.00mV(±2%) |
| Asystole (ASYS) | |
| Ventricular Fibrillation – Coarse (VFBC) | 240 BPM, Amplitude 1.00mV(±2%) |
| Ventricular Fibrillation – Fine (VFBF) | 240 BPM, Amplitude 1.00mV(±2%) |
| Monomorphic Ventricular Tachycardia (MVT) | 210 BPM, Amplitude 1.00mV(±2%) |
| Atrial Fibrillation (AFB) | 20 – 300 BPM, Amplitude 1.00mV(±2%) |
| ECG Waveforms – Sinus | |
| Normal Sinus Rhythm (NSR) | 20 – 300 BPM, Amplitude 0.50 – 5.00mV(±2%) |
| ST Elevation (STE) | 20 – 300 BPM, Amplitude 0.50 – 5.00mV(±2%) |
| ST Depression (STD) | 20 – 300 BPM, Amplitude 0.50 – 5.00mV(±2%) |
| Myocardial Infarction (MI) | 20 – 300 BPM, Amplitude 0.50 – 5.00mV(±2%) |
| Tall T (TT) | 20 – 300 BPM, Amplitude 0.50 – 5.00mV(±2%) |
| Asystole (ASYS) | |
| ECG Waveforms – Atrial Conduction Arrhythmias | |
| First Degree AV Bock (FAVB) | 80 BPM, Amplitude 0.50 – 5.00mV(±2%) |
| Second Degree AV Block – Mobitz I (SAVB_MI) | 80 BPM, Amplitude 0.50 – 5.00mV(±2%) |
| Second Degree AV Block – Mobitz II (SAVB_MII) | 80 BPM, Amplitude 0.50 – 5.00mV(±2%) |
| Third Degree AV Block (TAVB) | 50 BPM, Amplitude 0.50 – 5.00mV(±2%) |
| ECG Pacer Waveforms | |
| Synchronous Atrial (AAI) | 20 – 300 BPM, Pulse amplitude 0.50 – 5.00mV, Pulse width 0.1 – 2.0ms |
| Asynchronous Atrial (AOO) | 20 – 300 BPM, Pulse amplitude 0.50 – 5.00mV, Pulse width 0.1 – 2.0ms |
| Pacer (PCR) | 20 – 300 BPM, Pulse amplitude 0.50 – 5.00mV, Pulse width 0.1 – 2.0ms |
| Ventricular Pacer (VVI) | 20 – 300 BPM, Pulse amplitude 0.50 – 5.00mV, Pulse width 0.1 – 2.0ms |
| Atrial & Ventricular Pacer (DDD) | 20 – 300 BPM, Pulse amplitude 0.50 – 5.00mV, Pulse width 0.1 – 2.0ms |
| R-Wave Detection (RWD) | 20 – 300 BPM, Pulse amplitude 0.50 – 5.00mV |
| ECG Noise Selection | |
| Amplitude | Default Spec Value0 – 10.00mV |
| Frequency | 50 – 60Hz |
| ECG Accuracy | |
| Rate | Default Spec Value± 1% |
| Amplitude | ± 2% (LA-LL), ± 10% (Paddles) |
| Lead II : 1 – 10 mV (in steps of 0.5 mV). | |
| Other leads are proportional to Lead II by the following percentages: | |
| Lead I : 60 % | |
| Lead II : 100 % | |
| Lead III : 40 % | |
| V1 : 63 % [ Reference LA ] | |
| V2 : 71 % [ Reference LA ] | |
| V3 : 68 % [ Reference LA ] | |
| V4 : 80 % [ Reference LA ] | |
| V5 : 55 % [ Reference LA ] | |
| V6 : 49 % [ Reference LA ] | |
| Pacer Manufacturer Algorithms | |
| CU Medical, GE, HP, Laerdal, Mindray, Philips, PhysioControl, Schiller, WelchAllyn, Zoll | |
| Pacer Sensitivity Test | |
| Wave form, R Wave | Polarity Normal and Reversed, selectable |
| Dynamic Sensitivity | 0.05mV to 5.00mV in 50µV steps |
| General Specifications | |
| Dimensions | 220mm x 150mm x 90mm (L x W x H) |
| Weight | 1.5kg |
| Operation | 9.6V/2400mAh Nickel Metal Hydride battery pack |
| Battery charge time | 2.5 hours |
| Battery capacity (fully charged) | 12 hours |
| Mains supply | 110/230V AC; 48 to 66Hz, 35VA power supply |
| Storage environment | -15°C to +60°C |
| Operating conditions | 0°C to +40°C |
| Environmental protection | IP 40 |
| Communication | USB |
| Display LCD colour graphic display | ¼” VGA |
| Memory | 100 test results including graphs |
| Impact rating | 5J |
| Defib – Energy Measurement | |
|---|---|
| Load Resistance | 50Ω ± 1% non-inductive |
| Range | 0 – 199.9 Joules |
| Accuracy | ± 1% of reading ± 1 Joule |
| Range (High) | 200 – 600 Joules |
| Resolution | 0.1 Joules |
| Voltage | 0 – 5000 Volts |
| Current | 0 – 100 Amps |
| Maximum pulse width | 5μs – 120ms |
| ECG Simulator | |
| ECG simulation with hi-level output. | |
| ECG Waveforms – Ventricular Arrhythmias | |
| Premature Ventricular Contraction – Intermittent 80 BPM, Amplitude 0.50 – 5.00mV(±2%) | Default Spec Value |
| (PVCI) | |
| Bigeminy (BIG) | 80 BPM, Amplitude 0.50 – 5.00mV(±2%) |
| Trigeminy (TRIG) | 80 BPM, Amplitude 0.50 – 5.00mV(±2%) |
| Ventricular Flutter (VFLT) | 240 BPM, Amplitude 0.50 – 5.00mV(±2%) |
| Ventricular Fibrillation – Coarse (VFBC) | 240 BPM, Amplitude 0.50 – 5.00mV(±2%) |
| Ventricular Fibrillation – Fine (VFBF) | 240 BPM, Amplitude 0.50 – 5.00mV(±2%) |
| Monomorphic Ventricular Tachycardia (MVT) | 210 BPM, Amplitude 0.50 – 5.00mV(±2%) |
| Right-focal Premature Ventricular Contraction | 80 BPM, Amplitude 0.50 – 5.00mV(±2%) |
How do I download data from the UniPulse 400 to Med-eBase?
This application note details how to download results and communicate between the Uni-Pulse 400 and Med-eBase
On Med-eBase
1) First open Med-eBase Version 2.3 or higher
2) Select the Download from Tester icon which is situated on the top left hand side of the screen or in Tools and Download…
3) Select UniPulse-400 from the drop down list and confirm the COM port for the USB serial connection.
4) Then select Ok.
On The Uni-Pulse 400
5) From the main menu Select Data by selecting the enter key and then use the up and down arrows to select how you would like to search for the results to download; Asset ID, Make, Model, Serial number etc. then select F5 Search to find results.
6) Selecting F4 Download to PC allows the user the either Download selected items or Download all search items?
7) Then confirm selection with F4 confirm.
8) Then select USB or Bluetooth. Then confirm selection with F4 confirm.
Note: Currently Med-eBase transfer can only be conducted via USB.
9) During transfer a bar appears on both Med-eBase and the Uni-Pulse
10) When the download is complete and summary box appears on Med-eBase to enable the user to view what has been downloaded successfully.
Can I print a multiple results for a group of assets on Med-eBase?
The print function can allow for an individual asset result or multiple result certificates to be printed. Results certificates must be of the same type (e.g. 288) and under the same client, in the asset browser, to be printed in multiples.
1) You would need to select the first asset from the main asset browse screen
2) Then while pressing ctrl select any additional assets. All selected assets should be highlighted.
3) Then select the Print icon on the right hand side and select the Device type.
4) Then select OK and the generate certificate menu opens to allow you to scroll through the certificates, set the template and add additional details etc before printing or saving the certificates as PDF.
How do I download data from the Rigel devices to the PC without Med-eBase?
Equipment required:
- Rigel device
- PC/Laptop
- Bluetooth connectivity or RS 232 cable
- DataTransfer.exe for file transfer
There are 3 ways to send test results from the Rigel device to a PC:
1) Bluetooth connection
2) Serial connection using the RS 232 cable
3) USB (Only applicable for Performance Analysers)
Bluetooth connection
To download via Bluetooth the download is always initiated by the Rigel tester and can be saved as:
i. Text file
ii. Csv file
iii. To Med-eBase as SSS file (Please see the FAQ ‘How Do I Download Data from the Rigel Devices to Med-EBase?’)
Make sure the PC and Rigel device are paired via Bluetooth Favourites on the device (Please see FAQ ‘What’s the process for pairing devices using Bluetooth favourites’)
For 288+ and Sim Range test instruments
1) Select F4 and then D Data transfer.
2) On the PC, open the DataTransfer.exe program (This is available as a free download from rigelmedical.com).
3) Select Capture then start capture (See Figure 1)
Figure 1. Start capture on DataTransfer.exe
4) Choose a save name and location and change the file type to either .csv or .txt and press Save (See Figure 2)
Figure 2. Save file type on DataTransfer.exe
5) Back on the Rigel device select D Download to PC then F4 to confirm
6) An hour glass appears in the right hand corner while the Rigel device pairs with the PC Bluetooth and should turn to a
Bluetooth sign when it is connected.
7) F4 Send to start sending data from the tester.
8) Once the transfer of data is complete go to the Datatransfer.exe program select Capture then stop capture.
9) The data will now be saved in your chosen location as either a csv or txt file.
Serial connection using the RS 232 cable (Rigel 62353+)
To download using RS 232 the connection use the same method as for Bluetooth however the COM port will always be through COM1.
For Performance Analysers (Uni-Therm)
1) Select Menu, then Data and Transfer Data (See Figures 3 & 4)
Figure 3. Uni-Therm Data Figure 4. Uni-Therm Transfer Data
2) Follow steps 2 to 4 from previous method.
3) On the Uni-Therm press F2 Format to change the file format to either CSV Full or CSV Summary for transfer to PC.
4) Press F3 Port to change the download port to Bluetooth (See Figure 5)
Figure 5. Changing the download port
5) Press F4 START to begin the transfer.
6) When the Data Transfer is complete follow steps 8 and 9 from previous method.
Serial connection using the RS 232 cable
To download using RS 232 the connection use the same method as for Bluetooth however the COM port will always be through COM1.
USB connection Performance Analysers only (Uni-Therm)
1) Install the ERT1557USB driver. (This driver is available as part of the Uni-Therm firmware download, or on request from support@rigelmedical.com)
2) Connect the USB lead between the Rigel unit and the PC.
3) Select Menu, then Data and Transfer Data
4) Select F2 Format and change it to USB.
5) Open DataTransfer.exe and select COM1 from the drop down menu and then set the Bits per second field to 115200 and click Apply.
6) Follow the steps from previous method using Datatransfer.exe program
How do I set up the Bluetooth scanner?
Rigel Med-eBase Installer V2.6.2 (30 Day Trial included)
How do I pair my Rigel device via Bluetooth on Windows 10?
On the computer, select settings within the start menu and search for 'Bluetooth and other devices'. Select 'Add Bluetooth or other device'.
Next, add a BT device by selecting incoming devices.
Navigate to the device manager.
You will notice a BT com port and a serial com port
Open the serial com port by right clicking and selecting properties.
Correctly enter the port settings, as seen in the picture and then select advanced settings.
Make sure that the FIFO buffer's are not selected, and are switched off
Your BT port should now be linked with the serial to BT
You should now be able to download to Med-eBase or via DataTransfer.
Rigel Medical Brochure
How do you download results from the UniPulse 400 to Med-eBase?
This application note details how to download results and communicate between the UniPulse 400 and Med-eBase. Note this can only be performed when the UniPulse 400 is connected to the PC using a USB lead.
On The UniPulse 400:
1) From the main menu use the up and down keys and Select Data using the Enter key and then again use the up and down keys to select how you would like to search for the results to download.
2) (a) The keyboard can be used to enter the Asset ID, Make, Model, Serial number or Date(s) and then searched using F5
Note, the Bluetooth scanner can be used to enter the Asset ID and Serial number.
or
(b) The left and right keys can be used to select the Test type or Test status and then searched using F5.
or
(c) Find all test results by selecting F5 without making any changes.
Note: Any changes can be reset using the delete F3.
3) The Search results screen allows assets to be deleted using F2, printed using F3, downloaded to PC using F4 or viewed on the instrument using with F5.
4) Selecting download to PC, F4 allows the user to select either Download selected item? or Download all search items?
5) This selection is confirmed with F5, the instrument will then displays the sending screen.
On Med-eBase:
6) Using Med-eBase version 2.6 or higher.
7) With a database open, select the Download from Tester icon which is situated on the top left hand side of the screen or in Tools and Download…
8) Select UniPulse 400 from the Instrument Type drop down and confirm the COM port for the USB serial connection.
Note: the Set UP400 Clock using computer time can be used to set the time on the UniPulse 400 if required.
9) Select Ok.
10) During transfer a bar appears on both Med-eBase and the UniPulse 400 or UniPulse.
11) When the download is complete a Download Report appears on Med-eBase to enable the user to view what has been downloaded successfully.
12) On the instrument, Sending complete will be displayed.
UniPulse USB Driver
How do I use the variable load box?
The Variable load box allows the user to select different load settings for measuring the energy characteristics of a defibrillator under different patient (load) conditions as is required by IEC 60601-2-4.
Connect the variable load box to the defibrillator analyser using the black, red and grey connectors on the back panel:
When used in combination with the Rigel UNI-PULSE, the grey wire is the sense cable and will allow the UNI-PULSE to measure the set resistance to help avoid incorrect test setup.
Selecting the right resistance:
Use the supplied jumpers to select the required resistance. Bear in mind that the two COM connections (blue and black) are part of the setup and must correspond in colour with the selected load resistance as shown below for example 100 Ohm (black) and 75 Ohm (blue):
The selected resistance of the variable load box will appear on the UNI-PULSE when the OHM button is pressed;
UniPulse 400 SSS to CSV Converter
UniPulse 400 Firmware Update
What are the external load resistance configurations on the UniPulse 400?
If an external defib load is selected on the UniPulse 400, the user requires suitable external resistance. An internal resistance of 50Ω is always in circuit.
For 25Ω – a suitable 50Ω should be placed in parallel with the internal 50Ω of the UniPulse 400. For 75Ω,125Ω and 175Ω, additional resistance in 50Ω steps must be placed in series with the 25Ω parallel circuit.
For 100Ω, 150Ω, and 200 Ω, a suitable resistance should be placed in series with the internal 50 Ω. The figures below detail the configuration.
Register your product today to activate your warranty and to stay up to date with the latest product updates, news and support information.
If you wish to calibrate your UniPulse 400, please locate the nearest service center or contact us directly using the link below.
Sign up to our mailing list today to stay up to date with the latest industry news and information from Seaward.
Contact us
Email: sales@rigelmedical.com
Switchboard: +44 (0) 191 586 3511
Phone: +44 (0) 191 587 8730
